TBreakbuster
Golf Balls || BREAKBUSTER
PUTTER || Laser
Sharp || Shoulder Blade Square
The BREAKBUSTER
GOLF BALLS have these unique lines ENGINEERED and SCIENTIFICALLY
CALIBRATED to correspond to a particular break. Knowledge of physics,
angles, and gravity plus three years of research and development
have yielded this design that is SO SIMPLE TO USE AND REALLY WORKS!
Each line is calibrated at one inch of break per foot of putt!
Anything in between is estimated between one quarter and three
quarters inch!
Breakbuster
Golf Balls
1. There are ways to gauge the slope of the green. One
is, while walking towards the green; look at your ball on to the
hole and on to the edge of the green. This particular slope is
consistent from the ball location to the hole and the edge of
the green as shown in the picture. This particualr slope is consistent
all the way. The edge of the green in most cases is a very visible
slope indicator.
2.
By looking at the ball location to the cup. A slanting cup is
also a good indicator. Check for consistency.
3. Do steps
1 and 2 but in the opposite direction if there is
time available to do so while playing to verify your first assessment
of the
slope.

Using the
middle reference line as the horizontal base. The closest slope
as the green is the second line in the L/R area. Now point the
second line(red line) towards the middle of the hole.
NOTE(s): It
is important to putt one (1) to one and a half feet (1.5') past
the hole. In this case aim two inches right of the hole center.
The black dot of the reference line should be at top dead center.
<<
Return To Top >>
BREAKBUSTER
PUTTER
Patent pending
(photo
not yet available)
This special putter is made of Stainless Steel and have adjustable
lie. It is important to note that most players have different
preference in their putting technique. An adjustable lie will
enhance an individuals feel and thus putts better. Innovative
sighting to complement the
Breakbuster golf ball and a special handle with our logo.
Head weight
335 grams
Loft 3"
Lie 68-80 degree
<< Return To Top >>
Laser
Sharp Training Aid
How to make sure
your aim is correct!!!
Through Engineering
and common sense approach, we introduce to you the Laser Sharp
Putting and Chipping System.
The Laser
Sharp Training Aid consists of:
1. Carousel with 360 degrees turn for unlimited target
2. Linear Laser with putter activated switch on top of the carousel.
3. Two trays wit a 50-ball capacity each and width adjustable.
Space between trays is for the putter head path. The smaller the
clearance, the better putter you become. Hit the trays and
The swing is not straight.
4. L-stick for parallel feet and posture alignment.
Putt and Chip straight with the aid of the linear Laser.
Place the ball on the platform and point the ball at your target.
Most people are left or right eye dominant. To verify if your
aim is correct, the laser sharp has a laser underneath and when
you press the switch with your putter, the laser will show where
you are aiming. If you are constantly aiming to the right, then
you are a right eye dominant (or vice versa) and thus
make
the adjustment. This is one attribute of this training aid.
<<
Return To Top >>
Shoulder
Blade Square (SB2 )
Execution!!!
Introducing the Shoulder Blade Square(SB2 )
No matter how good is your aim, the right execution is critical.
The technology behind the SB2 is simple. By making both shoulder
like a straight line, positioning them perpendicular to the putter
face, and putting with a pendulum motion, the swing is straighter
and more accurate. Attaching the SB2 to the shaft of the putter
and adjusting the "T" part until it is perfectly square
or at 90 degrees with the putter face. The gooseneck part of the
SB2 is for easy adjustment for each individual putting posture height
and space preference.
When putting, the ends of the "T" part are touching both
ends of the shoulder blade (both at equal pressure). The hands contribution
at this time is just to hold the putter. The upper body is making
the pendulum motion and because of its mass, it is steadier. Practice
and you will see the difference in your consistency and accuracy.
<<
Return To Top >>